Is your Whirlpool Cabrio washer displaying error codes on its LCD panel? Don’t worry, understanding these error codes can help you identify and resolve common problems with your washer. In this article, we will guide you through various error codes and provide troubleshooting steps to help get your washer back up and running smoothly.
Key Takeaways:
- Whirlpool Cabrio washers display error codes on the LCD panel.
- Error codes can be a combination of letters and numbers or flashing lights with beeping sounds.
- Refer to the owner’s manual for a clear explanation of error codes and instructions for diagnostic mode and resetting.
- We will cover common error codes like LF, Ld, uL, oL, Sd, lid, Po, HC, dL, and dU, and provide troubleshooting steps for each.
- If the problem persists or you need further assistance, consult the owner’s manual or seek professional help.
LF (F30) – Long Fill Error
The LF error code on your Whirlpool Cabrio washer indicates a long fill error. This means that the water level does not change after the valves are turned on or after water has left the drum. It’s important to resolve this issue promptly to ensure proper functioning of your washer.
If you encounter the LF error code, there are a few troubleshooting steps you can take to address the problem:
- Check the water supply: Ensure that the water supply to the washer is connected and turned on. Sometimes, a loose or disconnected water supply hose can cause the long fill error.
- Inspect hose screens: Clogs in the hose screens can restrict water flow and trigger the LF error code. Clean any debris or sediment from the screens to ensure smooth water flow.
- Verify water flow into the tub: Make sure that water is actually entering the tub of the washer. If no water is entering, there may be an issue with the water supply valve or the inlet valve.
- Check the pressure hose connection: The pressure hose connection to the machine or motor control can also contribute to the long fill error. Inspect the connection and ensure it is secure.
By following these troubleshooting steps, you can effectively resolve the LF (F30) long fill error on your Whirlpool Cabrio washer and ensure that it functions optimally.
If you require further assistance or the issue persists, it is recommended to consult the owner’s manual or reach out to a professional technician for repair.
Ld (F32) – Long Drain Error
The Ld error code is an indication of a long drain issue in your Whirlpool Cabrio washer. This error appears when the water level fails to change after the drain pump is activated. The most common causes of the Ld error code are a clogged drain hose or a malfunctioning drain pump.
To troubleshoot and resolve this problem, follow these steps:
- Check the drain hose: Ensure that the drain hose is properly installed and free from any blockages. A clogged drain hose can prevent the water from draining effectively.
- Inspect the drain pump: Examine the drain pump for any signs of damage or malfunction. A faulty drain pump can also result in a long drain error.
- Verify the drain hose height: Ensure that the drain hose is positioned at a height greater than 96 inches. If the drain hose is too low, the water may not drain properly, triggering the Ld error code.
If you have checked these possible causes and the issue persists, it is recommended to consult a professional technician or contact the Whirlpool customer support for further assistance.
Here is an illustration showing the typical setup of a Whirlpool Cabrio washer with a drain pump:
| Component | Description |
|---|---|
| Drain Pump | |
| Drain Hose | |
| Drain Hose Height | Higher than 96 inches |
uL – Unbalanced Load
The uL error code indicates an unbalanced load in your Whirlpool Cabrio washer. This error code will remain on while the washer runs a mini-cycle to rebalance the load. If the mini-cycle is unsuccessful, the uL code will begin to flash.
To resolve this issue, you need to check for an off-balance load and redistribute the laundry to ensure a balanced load. Make sure that the clothes are distributed evenly in the drum. Large and bulky items, such as blankets or comforters, can cause an unbalanced load. Try removing these items and running the cycle again.
If the problem persists, it could indicate a problem with the suspension rods. The suspension rods support the drum and help keep it balanced during the wash cycle. Inspect the suspension rods for damage, such as visible wear or breakage. If you notice any damage, consider replacing the suspension rods to restore proper balance to your washer.
You can refer to the table below for a summary of troubleshooting steps for the uL error code:
| Steps to resolve uL error code (Unbalanced Load) |
|---|
| 1. Check for an off-balance load. |
| 2. Redistribute the laundry to ensure a balanced load. |
| 3. Remove large and bulky items from the drum. |
| 4. Inspect the suspension rods for damage. |
| 5. Consider replacing the suspension rods if necessary. |
If you have followed these steps and the uL error code persists, it is recommended to seek professional assistance or contact Whirlpool customer support for further assistance.
oL (F70) – Overloaded
The oL error code signifies that the washer is overloaded, meaning the load size exceeds the machine’s capacity. When this error code appears, the washer may experience issues and fail to operate properly. However, this can be easily resolved by following a few simple steps:
- Open the lid of the washer to clear the display.
- Remove excess laundry from the washer drum.
- Close the lid and restart the cycle.
By reducing the amount of laundry and ensuring it is within the recommended capacity, the oL error code should no longer appear, allowing the washer to function as expected.
Remember, overloading the washer not only triggers the oL error code but also affects the efficiency and performance of the machine. Avoid overloading the washer to maintain its longevity and effectiveness.
| Error Code | Description |
|---|---|
| oL (F70) | The washer is overloaded, exceeding its capacity. |
Sd (F71) – Suds Detection
When you see the Sd error code on your Whirlpool Cabrio washer, it indicates a suds-lock condition caused by excessive detergent usage, failure to engage the basket during the drain step, or mechanical friction on the drive mechanism.
The control system of the washer is designed to detect excessive suds and automatically run a mini clean-out cycle to correct the problem. This cycle helps remove the excess suds and clear the drain system. However, if the clean-out cycle is unsuccessful, the Sd code will continue to flash on the display, indicating that further action is needed.
To resolve the Sd error code, follow these steps:
- Stop the washer and unplug it from the power source.
- Check the detergent usage and ensure you are using the correct amount. Excessive detergent can cause excessive suds.
- Inspect the drain step and make sure it is functioning properly. Clean any clogs or obstructions that may be affecting the drainage.
- Check the drive mechanism for any signs of mechanical friction. Worn-out parts may need to be replaced to ensure smooth operation.
- Once you have addressed these potential causes, plug the washer back in and restart the cycle. The Sd error code should no longer appear if the issue has been resolved.
By following these troubleshooting steps, you can effectively resolve the Sd error code on your Whirlpool Cabrio washer and ensure optimal performance.
| Possible Causes | Resolution |
|---|---|
| Excessive detergent usage | Use the correct amount of detergent according to the manufacturer’s instructions. |
| Failure to engage basket during drain step | Clean any obstructions or clogs in the drain system. |
| Mechanical friction on the drive mechanism | Inspect and replace worn-out parts as necessary. |
lid (F81) – Open/Close Door Lid
The lid error code (F81) indicates issues with the door lid of your Whirlpool Cabrio washer. This error can occur if the lid is open when the START button is pressed or if the lid is not opened after two consecutive machine cycles. The control system is unable to detect the proper opening and closing of the lid switch, resulting in the F81 error code.
To resolve this error, first, check if the lid is properly closed when starting a cycle. Make sure to press the START button only when the lid is securely closed. If the lid is already closed and the error persists, try opening and closing the lid a few times to ensure it is making proper contact with the lid switch.
If the issue continues, inspect the lid switch for any visible damage or loose connections. The lid switch is a safety feature that prevents the washer from operating if the lid is open. If the switch is faulty, it may need to be replaced to resolve the F81 error code.
Here is an illustration to help you understand the open/close door lid error:
| Cause | Solution |
|---|---|
| The lid is open when START button is pressed | Close the lid properly before starting a cycle |
| The lid is not opened after two consecutive machine cycles | Open and close the lid a few times to ensure proper contact with the lid switch |
| Faulty lid switch | Inspect the lid switch for damage or loose connections; replace if necessary |
Po – Pump Out (lid opened)
The Po error code indicates that the drain pump has started pumping out water from the tub because the door lid has been left open for more than 10 minutes. To stop the drain pump from operating, simply close the door lid.
Po Error Code Troubleshooting Steps:
- Ensure that the door lid is completely closed.
- Check if the door lid sensor is functioning properly.
- If the issue persists, restart the washer after closing the door lid securely.
It is important to close the door lid properly to prevent unnecessary draining and ensure the washer operates efficiently.
| Error Code | Meaning | Action |
|---|---|---|
| Po | Pump Out (lid opened) | Close the door lid to stop draining. |
| LF | Long Fill Error | Check water supply and pressure hose connection. |
| Ld | Long Drain Error | Inspect drain pump and check drain hose height. |
| uL | Unbalanced Load | Redistribute laundry and check suspension rods. |
HC – Hot, Cold Reversed
The HC error code on your Whirlpool Cabrio washer indicates that the hot and cold inlet hoses are connected in reverse. This can lead to issues with the water temperature during a wash cycle.
To resolve this error, it is important to ensure that the inlet hoses are correctly connected to their respective valves. The hot water inlet hose should be connected to the hot water valve, and the cold water inlet hose should be connected to the cold water valve.
If you are experiencing the HC error code, follow these steps to correct the hot and cold water connection:
- Turn off the water supply to the washer.
- Unscrew the inlet hoses from the back of the washer.
- Identify the hot water inlet hose, which is usually marked with a red ring or tag.
- Connect the hot water inlet hose to the hot water valve on the wall or faucet.
- Identify the cold water inlet hose, which is usually marked with a blue ring or tag.
- Connect the cold water inlet hose to the cold water valve on the wall or faucet.
- Tighten the inlet hoses securely to prevent leaks.
- Turn on the water supply and check if the HC error code has been resolved.
If the error code persists after ensuring correct hose connections, there may be an issue with the water valves or the washer’s control board. In such cases, it is recommended to contact a professional technician for further assistance.
dL (F80, 82, 84, 85) – Door Lock Failure
The dL error code is an indication of a door lock failure on your Whirlpool Cabrio washer. This error can occur due to various reasons, such as the door lid not being closed properly, lint and detergent residue interfering with the lock bolt, or the control detecting an open door lid switch. To troubleshoot and resolve this issue, follow the steps below:
- Ensure that the door lid is closed completely. Check for any obstructions or items that may prevent the lid from closing properly.
- If there is lint or detergent residue on the lock bolt, clean it using a damp cloth. This will help to ensure smooth locking and unlocking of the door.
- Verify that the door lid is in a locked state. If necessary, gently press down on the lid to ensure a secure lock.
If the problem persists, it may be necessary to replace the main control assembly. Contact a professional technician or Whirlpool customer service for assistance with replacing the main control assembly.
Comparison of dL Error Codes
| Error Code | Description |
|---|---|
| F80 | Door lock failure |
| F82 | Door lock failure |
| F84 | Door lock failure |
| F85 | Door lock failure |
dU (F83) – Door Unlock Failure
In some instances, the Whirlpool Cabrio washer may encounter a door unlock failure, indicated by the dU error code (F83). This error occurs when there are issues with the door unlock process, preventing the lock bolt from retracting or obstructing its movement. Two common causes of this error are excessive force on the door lid and wash residue blocking the lock bolt’s path.
To resolve the dU error code, start by checking if there is any excessive force applied to the door lid. Ensure that nothing is obstructing the proper operation of the lock bolt. If necessary, gently clear any obstructions or debris that may be blocking the lock bolt’s movement.
It’s also important to inspect the washer for wash residue, as this can accumulate over time and impede the lock bolt’s functionality. If you notice any visible residue, gently clean the affected areas using a mild detergent and a soft cloth or sponge.
Once you have cleared any obstructions and addressed any wash residue, make sure that the door lid is in an unlocked state before starting or restarting the washer. Double-check that the door lid is securely closed and that there are no items preventing it from fully closing.
If the dU error code persists after following these steps, it may be necessary to replace the door lock/switch assembly. In such cases, it is recommended to consult a professional technician or contact Whirlpool customer support for further assistance.
For a quick overview of the troubleshooting steps for dU (F83) error code on a Whirlpool Cabrio washer, refer to the following table:
| Steps to Resolve dU (F83) Error Code |
|---|
| 1. Check for excessive force on the door lid |
| 2. Clear any obstructions blocking the lock bolt |
| 3. Clean any wash residue interfering with the lock bolt’s movement |
| 4. Ensure the door lid is in an unlocked state |
| 5. Securely close the door lid and remove any items obstructing it |
| 6. If the error persists, consider replacing the door lock/switch assembly |
Conclusion
Troubleshooting error codes on a Whirlpool Cabrio washer can be a valuable tool for identifying and resolving common issues. By understanding the meaning behind each code and following the recommended steps for repair, users can effectively troubleshoot and fix problems with their washer. It’s essential to always refer to the owner’s manual for specific instructions and guidelines. If the problem persists or if you’re unsure about any repair steps, it’s recommended to seek professional assistance to ensure a safe and proper resolution.
Whirlpool Cabrio washers are equipped with advanced error code systems that provide valuable diagnostic information. By using these error codes as a guide, users can diagnose issues related to water supply, drain pump, unbalanced loads, excess detergent, lid issues, and more. Resolving these problems promptly can help prevent further damage to the washer and ensure optimal performance.
Remember, troubleshooting and repairing your Whirlpool Cabrio washer yourself can save time and money. However, it’s crucial to exercise caution and prioritize safety. Always disconnect the power supply before performing any repairs or inspections. If you’re uncomfortable or unsure about any repair steps, reach out to a qualified technician or Whirlpool customer service for professional assistance. Your Whirlpool Cabrio washer is an investment, and with proper care and maintenance, it can provide years of reliable service.
FAQ
What does the LF (F30) error code on my Whirlpool Cabrio washer indicate?
The LF error code indicates a long fill error, meaning the water level does not change after the valves are turned on or after water has left the drum. To resolve this issue, check if the water supply is connected and turned on, and inspect hose screens for clogs. Also, verify if water is entering the tub and check the pressure hose connection to the machine/motor control.
Why am I seeing the Ld (F32) error code on my Whirlpool Cabrio washer?
The Ld error code appears when the water level does not change after the drain pump is on. This can be caused by a clogged drain hose or drain pump. Check for proper installation and ensure the drain hose is higher than 96 inches.
What should I do if my Whirlpool Cabrio washer displays the uL error code?
The uL error code indicates an unbalanced load, and it remains on while the washer runs a mini-cycle to rebalance the load. First, check for an off-balance load and redistribute the laundry to ensure a balanced load. If the problem persists, inspect the suspension rods for damage and consider replacing them.
How can I resolve the oL (F70) error code on my Whirlpool Cabrio washer?
The oL error code signals an overloaded washer, where the load size exceeds the machine’s capacity. To resolve this issue, open the lid to clear the display, remove excess laundry, and restart the cycle.
What does the Sd (F71) error code mean on my Whirlpool Cabrio washer?
The Sd error code indicates a suds-lock condition due to excessive detergent usage, failure to engage the basket during the drain step, or mechanical friction on the drive mechanism. The control runs a mini clean-out cycle to correct the excess suds problem. If the clean-out cycle is unsuccessful, the Sd code will continue to flash in the display.
Why is the lid error code (F81) flashing on my Whirlpool Cabrio washer?
The lid error code (F81) flashes when there are issues with the door lid. This can occur if the lid is open when the START button is pressed or if the lid is not opened after two consecutive machine cycles. The control cannot detect the proper opening and closing of the lid switch.
How do I stop the drain pump from operating when the Po error code appears on my Whirlpool Cabrio washer?
The Po error code appears when the drain pump starts pumping out water from the tub because the door lid has been left open for more than 10 minutes. Simply close the door lid to stop the drain pump from operating.
What should I do if my Whirlpool Cabrio washer shows the HC error code?
The HC error code indicates that the hot and cold inlet hoses are connected in reverse. Make sure the inlet hoses are connected correctly to their respective valves.
Why is the dL error code flashing on my Whirlpool Cabrio washer?
The dL error code flashes when there are issues with the door lock. This can occur if the door lid is not closed completely, lint and detergent residue interfere with the lock bolt, or the control detects an open door lid switch. Check for interference, clean the latch if necessary, and ensure the door lid is in a locked state. If the problem persists, the main control assembly may need to be replaced.
How can I resolve the dU error code on my Whirlpool Cabrio washer?
The dU error code flashes when there are issues with the door unlock process. This can occur if excessive force on the door lid prevents the lock bolt from retracting or if there is wash residue blocking the movement of the lock bolt. Clear any obstructions and ensure the door lid is in an unlocked state. If the problem persists, the door lock/switch assembly may need to be replaced.
